Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 2 Next »

In firmware 1.20 the way call routing was configured has been changed. In this FAQ you are going to find out what is different from previous firmware versions.

 

On 2N® VoiceBlue MAX following changes have been done:

  • In Gateway configuration there is no longer option to select port modes, where you were able to select how calls incoming from one port should be routed (basically allowing you to route calls from FXS to GSM or VoIP). This setting has been merged into LCR table offering an easier configuration.
  • LCR table has been redone.


New LCR table allows you to have a complete control over where an incoming call (from VoIP, GSM or FXS interfaces) should be routed to. On pictures bellow you can see examples of differences between the new LCR table and the old one.

1) Explanation of new LCR table

From (channels/groups) - this parameter specifies where outgoing call originates. In case of VoiceBlue Max it can be:

  • all GSM channels
  • specific GSM incoming group (1-2)
  • FXS ports, all channels
  • FXS port, specific channel (0-3)
  • VoIP 

Prefix list - this parameter's effect is the same as in previous firmware versions

Groups/Tarrifs - this parameter specifies if outgoing call should go through a specifis GSM outgoing group, VoIP or FXS interfaces

This way you have a better control over how ougoing and incoming calls are handled and routed. Plus it is possible to route incoming calls from GSM back to GSM which was not possible in older firmware version.

2) Default LCR table settings

Firmware 1.20
Firmware 1.19 and older

 

In default there are 5 records which match the default setting of Port modes and LCR table from firmware 1.19 and older

You needed to setup both Port modes and LCR table.

3) Calls from FXS port 1 are routed directly to GSM outgoing group 1 (dialed number must match prefix list 1), outgiong calls from FXS port 2 are routed directly to GSM outgoing group 2 (dialed number must match prefix list 2), all other calls are left in default

Firmware 1.20
Firmware 1.19 and older

 

 

Calls coming from FXS port 0 (dialed number must match prefix list 1) are routed directly to GSM outgoing group 1.

Calls coming from FXS port 1 (dialed number must match prefix list 2) are routed directly to GSM outgoing group 2.

 

All other calls are routed as is in default

Routing calls from a specific port was dona based on the number that the person was dialing. In this scenario person calling from FXS port 1 must have dialed 01 XXXXXXXXX, caller from FXS port 2 must have dialed 02 XXXXXXXXX.

4) Incoming call from GSM group 2 (matching prefix list 2) will be routed back to GSM through GSM outoing group 1. Every other incoming call from GSM will be sent to FXS interfaces. Everything else is left in default.

Firmware 1.20
Firmware 1.19 and older
Sending incoming calls from GSM back to GSM was not possible
On picture above you can see how to set a scenario where all incoming calls from GSM incoming group 2
should be sent back to GSM through GSM outgoing group 1 (if dialed number will match Prefix list 2)
Sending incoming calls from GSM back to GSM was not possible
Sending incoming calls from GSM back to GSM was not possible

On the picture above you can see how to set described scenario.

All calls from GSM incoming group 2 (matching prefix list 2) are sent back to GSM.
All other calls from GSM are sent to FXS interfaces.

Sending incoming calls from GSM back to GSM was not possible

 

To find out more about how to setup call routing please look at FAQ:

  • No labels