Skip to end of metadata
Go to start of metadata

Please, follow the steps below what to check before you send the 2N® Net Audio Decoder / 2N® Net Audio Decoder Lite / 2N® Net Mic / 2N® Net Audio Encoder / 2N® Net Speaker  device for repair:

Possible issues:


a) Net Audio device does not boot up after plug in

b) Net Audio device is not reachable in the network/can not be found in the IP Audio Manager scanner

c) Net Audio device is visible in the scanner but is not connected to the IP Audio Manager (server)

d) Net Audio device is not working correctly, device is connected to the server but is not playing


As a first step check out the LED signalisation of the device. The meaning of each signalling can be found here:

LED indication for the 2N® Net Audio Decoder / 2N® Net Audio Decoder Lite 2N® Net Audio Decoder

LED indication for the 2N® Net Mic 2N® Net Mic


add a) Check the LAN cable connection and availability of the PoE or External power source for the IP Audio device. The PoE has a standard PoE IEEE 802.3af, the Erternal power source then 12V DC / 2A.

add b) Check the LAN cable connection and LAN network availability. In default setting the IP Audio device require the dynamic IP Address from the DHCP Server.

  • CAUTION  even if other devices in the network obtain  IP address automatically 2N IP audio unit   does not have to   due to the restrictions set by the IT department in the network. This setting automatically assigns IP addresses only to known / registered devices in the network based on their MAC addresses!

  • In case device did not obtain IP address automatically, go to  menu Administrator  > Net Audio device scanner . Displayed IP address in field  DHCP would be0.0.0.0(see picture below).
    For more details contact your IT department. In this case it could be MAC address restriction in the network. P rovide  MAC address of the device  to your IT departmentand they will register it and allow automatic assignment of the IP addresses . 

    Second option is to turn the  DHCP client  OFF and setup  IP address manually In this case  it is necessary to know some free IP address which can be used for 2N® Net Audio Decoder unit in the network. It means that this IP address (the one you would like to use) is not assigned to  any other IP device in the network (you can use ping command to check it). Do not forget to set up the IP mask = subnet of the network.

    Manual settings could look  like this:  IP address: IP mask:

  • Firewall can also block connection of the unit  to the 2N® IP Audio Manager
    Do you have firewall switched ON? It can cause that if 2N® Net Audio Decoder unit  disconnects from the server and then tries to connect again via the same port , firewall (eg, ESET Smart Security will not let it go through.  This is not the common issue  but it could be one of the reason why you cannot see 2N® Net Audio Decoder units in menu Destinations & Zones.    
    Picture n. 1 below   shows the situation   when the network   automatically   assigns   IP   addresses ( there is  DHCP   server in the network)   but the device   (e.g.  2N® Net Audio Decoder  unit   is not   recognized = IT department does not know its MAC address). In this case IP address for 2N® Net Audio Decoder unit would not be automatically assigned   .

Picture n.1

  • Picture n. 2 below shows an example of manually assigned IP address and IP mask, when  the DHCP client has been switched OFF:

Picture n.2

add c)   Check out the correct setting for the communication between the IP Audio Manager and the IP Audio unit. The device itself can work in three different modes. Setting bellow in the Picture n.3

  • Search mode - Check out the setting of the Domain, it has to correspond with the domain name of the Server-can be found in the Communication properties
  • Active mode - Check out the setting for the IP Audio Manager IP Address- it has to correspond with a IP Address of the Server

Picture n. 3

  • Password for authorization is used: IP audio device authentication to the Server / Server  authentication   to the IP audio device.

    IP audio device is not connected to the 2N® IP Audio Manager even all parameters as:  IP address, domain, connection mode  are set-up correctly?  Most probably you have previously used password for device/server authorization
    To be sure, there is authentication password used. You would need to connect via  Telnet  to already connected unit to the 2N® IP Audio Manager. For security reason it is needed to " Enable telnet " connection in menu  Destinations & Zones . Click on the unit which is already connected and in its parameters check option " Enable telnet ".      

Picture n.4

add d)  In case that the IP Audio device is correctly connected with a server but the Audio is not working, check out the connection and parameters of connected speakers

The Speaker has to be with a nominal impedance from 4 to 16 Ohms. All the parameters can be found in the table in the Picture n.5 below


Power 12V/2A


2 x 4 Ohm STEREO

2 x 2.5W

2 x 2.5W

2 x 8 Ohm STEREO

2 x 7W

2 x 4W

2 x 16 Ohm STEREO

2 x 4W

2 x 4W

4 Ohm MONO

1 x 14W

1 x 8W

8 Ohm MONO

1 x 8W

1 x 8W


Picture n. 5

Use the  2N ®  Net Audio Decoder  back panel terminals marked L + and L – for the left channel and R + and R – for the right channel. Use the left channel terminals for the MONO mode.

In any case of further failure please contact the Technical support with a full description what have you already with as much details and discuss the further steps.