Skip to end of metadata
Go to start of metadata

This FAQ describes how to setup direct call between 2N® LiftIP and 2N® Lift8 Communicator with a feed from a Revotech IP camera.

 

Info

Icon

 

* This parameter can be set via the voice menu (incoming call to 2N® LiftIP unit).

** This parameter can only be set via the 2N® LiftIP Service Tool.

A list of all parameters that can be configured can be seen in the manual: Programming Function Survey

 

In the Lift8 manual you can find how to get the 2N® Lift8 Communicator working: https://wiki.2n.cz/l8um/latest/en/8-communicator

 

Please keep in mind that if you will disable confirmation for alarm calls, then you are doing this at your own risk as there is no human interaction!

 

 

 

 

 

1) Connection to 2N® LiftIP

 

Connect to your 2N® LiftIP unit using 2N® LiftIP Service Tool which you can download - here

  • It is necessary to use the 2N® LiftIP Service Tool, as VoIP parameters can't be set via the voice menu (incoming call to 2N® LiftIP)

You can connect directly by choosing TCP and filling in the correct IP addressPort and Password
If you don't know the IP address, please use the FAQ - How to get IP address of lift communicator 2N® LiftIP.
If you need to set Static IP address or DHCP please use this FAQ - Static IP address - How to set up static IP address on 2N® LiftIP

Press Connect:




2) How to set the alarm call destination

 

Go to Configuration - Parameters - Alarm Call -> and set following parameters:

011 =* IP address and SIP port of the 2N® Lift8 Communicator - in our example we use "192.168.50.115:5070"
018 =* Count of automatic dialling cycles for ALARM (011-016) * - when the destination doesn't pickup, it calls again depending on the count of cycles you set

111 =* Alarm call memory confirmation mode  - defines how the call is confirmed after pick-up
  x1x = Alarm button (1-6)
  xx1 = Type of confirmation 

  • 1 = with DTMF confirmation (1)
  • 2 = with pick-up confirmation (for GSM/UMTS/VoIP only) - no confirmation, just pick-up the handset
  • 3 = CPC Antenna
  • 4 = CPC Kone
  • 5 = P100
  • 6 = DTMF auto detection (CPC Antenna/P100)
  • 7 = CPC Antenna 2N ext
  • 8 = CPC Kone 2N ext
  • 9 = P100 2N ext

You can find all parameters in the Programming Function Survey

Don't forget to click on Save to device

 

 

 

3) How to set the video stream from the Revotech camera

 

Go to Configuration - Parameters - RTSP Settings -> Set the following parameters:

1120 = RTSP address of the Revotech camera in the LAN - in this example: rtsp://192.168.50.207:8554/live0.264 is used.
1121 = user name for the web interface of the camera
1122 = password for the web interface of the camera

Don't forget to click Save to device:

 

Other possibilities of the Revotech stream address:

rtsp://<ip>:8554/cam0/h264

rtsp://<ip>:8554/ch0_0.264

rtsp://<ip>:8554/live1.264

 

 

 

4) Setting of the Revotech camera

 

Better to set lower parameters of the video stream under the section Video Stream in the web interface of the Revotech camera - example:

 

 

 

 

 

5) Setting of the 2N® Lift8 Communicator

 

1) Run the 2N® Lift8 Server - see in the manual, please: https://wiki.2n.cz/l8um/latest/en/6-lift8-server

 

2) Run the 2N® Lift8 ControlPanel - see in the manual, please: https://wiki.2n.cz/l8um/latest/en/7-control-panel

 

3) Enable direct SIP calls in the 2N® Lift8 ControlPanel (and save it below):

 

4) Run the 2N® Lift8 Communicator - see in the manual, please: https://wiki.2n.cz/l8um/latest/en/8-communicator

    and as the SIP port put the same one as for the alarm call number in the 2N® LiftIP Service Tool - in our case - 5070:

 

 

Now the 2N® Lift8 Communicator is ready to answer the alarm call from the 2N® LiftIP together with the stream of the IP camera.

 

Icon

If the camera picture wouldn't appear in the 2N® Lift8 Communicator, let disconnect WiFi connection on the PC.